Materials and Design, 0264-1275

Journal

ISSNs0264-1275, 0261-3069
Additional searchable ISSN (Electronic)1873-4197
1 - 10 out of 53Page size: 10

Research output

  1. 2021
  2. Published

    Multi-method characterization approach to facilitate a strategy to design mechanical and electrical properties of sintered copper

    Wijaya, A., Eichinger, B., Chamasemani, F. F., Sartory, B., Hammer, R., Maier-Kiener, V., Kiener, D., Mischitz, M. & Brunner, R., 1 Jan 2021, In : Materials and Design. 197, 109188.

    Research output: Contribution to journal › Article › Research › peer-review

  3. Published

    Open-cell tungsten nanofoams: Scaling behavior and structural disorder dependence of Young's modulus and flow strength

    Zhao, M., Schlueter, K., Wurmshuber, M., Reitgruber, M. & Kiener, D., 1 Jan 2021, In : Materials and Design. 197, 109187.

    Research output: Contribution to journal › Article › Research › peer-review

  4. 2020
  5. Published

    An analytical solution for the correct determination of crack lengths via cantilever stiffness

    Alfreider, M., Kolitsch, S., Wurster, S. & Kiener, D., 27 Jun 2020, In : Materials and Design. 194.2020, September, 3 p., 108914.

    Research output: Contribution to journal › Article › Research › peer-review

  6. Published

    Warm-forming of pre-aged Al-Zn-Mg-Cu alloy sheet

    Österreicher, J. A., Tunes, M. A., Grabner, F., Arnoldt, A., Kremmer, T., Pogatscher, S. & Schlögl, C. M., Jun 2020, In : Materials and Design. p. 108837 1 p.

    Research output: Contribution to journal › Article › Research › peer-review

  7. Published

    Room temperature recovery of cryogenically deformed aluminium alloys

    Gruber, B., Grabner, F., Falkinger, G., Schökel, A., Spieckermann, F., Uggowitzer, P. J. & Pogatscher, S., May 2020, In : Materials & design.

    Research output: Contribution to journal › Article › Research › peer-review

  8. Published

    Thermally activated deformation mechanisms and solid solution softening in W-Re alloys investigated via high temperature nanoindentation

    Kappacher, J., Leitner, A., Kiener, D., Clemens, H. & Maier-Kiener, V., 1 Apr 2020, In : Materials and Design. 189.2020, April, 6 p., 108499.

    Research output: Contribution to journal › Article › Research › peer-review

  9. Published

    Microstructures, mechanical properties and deformation of near-rapidly solidified low-density Fe-20Mn-9Al-1.2C-xCr steels

    Zhang, J., Hu, C., Zhang, Y., LI, J., Song, C. & Zhai, Q., 15 Jan 2020, In : Materials and Design. 186.2020, p. 1-13 108307.

    Research output: Contribution to journal › Article › Research › peer-review

  10. Published

    Fracture properties of thin film TiN at elevated temperatures

    Buchinger, J., Löfler, L., Ast, J., Wagner, A., Chen, Z., Michler, J., Zhang, Z., Mayrhofer, P. H., Holec, D. & Bartosik, M., 2020, In : Materials & design. 2020, 194, p. 1-10

    Research output: Contribution to journal › Article › Research › peer-review

  11. 2019
  12. Published

    Influence of crystal orientation and Berkovich tip rotation on the mechanical characterization of grain boundaries in molybdenum

    Jakob, S., Leitner, A., Lorich, A., Eidenberger-Schober, M., Knabl, W., Pippan, R., Clemens, H. & Maier-Kiener, V., 2 Jul 2019, In : Materials & design. 182.2019, 15 November, p. 1-9 9 p., 107998.

    Research output: Contribution to journal › Article › Research › peer-review

  13. Published

    Age-hardening of high pressure die casting AlMg alloys with Zn and combined Zn and Cu additions

    Stemper, L., Mitas, B., Kremmer, T., Otterbach, S., Uggowitzer, P. J. & Pogatscher, S., 9 Jun 2019, In : Materials & design. 181.2019, 11 p., 107927.

    Research output: Contribution to journal › Article › Research › peer-review

Previous 1 2 3 4 5 6 Next
View graph of relations