Materials science and engineering: A, Structural materials: properties, microstructure and processing, 0921-5093

Journal

ISSNs0921-5093
Additional searchable ISSN (Electronic)1873-4936

Research output

  1. Article › Research › Peer-reviewed
  2. Published
  3. Published
  4. Published
  5. Published
  6. Published
  7. Published

    Analysis of the Precipitation Behaviour in a High Speed Steel with Small Angle Neutron Scattering

    Leitner, H., Staron, P., Clemens, H., Marsoner, S. & Warbichler, P., 2005, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 398, p. 323-331

    Research output: Contribution to journalArticleResearchpeer-review

  8. Published

    Anisotropic fracture behavior of ultrafine-grained iron

    Hohenwarter, A. & Pippan, R., 2010, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 527, p. 2649-2656

    Research output: Contribution to journalArticleResearchpeer-review

  9. Published

    Annealing studies of nanocomposite Ti-Si-C thin films with respect to phase stability and tribological performance

    Rester, M., Neidhardt, J., Eklund, P., Emmerlich, J., Ljungcrantz, H., Hultman, L. & Mitterer, C., 2006, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 429, p. 90-95

    Research output: Contribution to journalArticleResearchpeer-review

  10. Published

    Back stress evolution and iso-volume fraction lines in a Cr-Ni-Mo-Al-Ti maraging steel in the process of martensitic transformation

    Nagayama, K., Terasaki, T., Goto, S., Tanaka, K., Antretter, T., Fischer, F. D., Cailletaud, G. & Azzouz, F., 25 Oct 2002, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 336, 1-2, p. 30-38 9 p.

    Research output: Contribution to journalArticleResearchpeer-review

  11. Published

    Changes in the mechanical properties of a pearlitic steel due to large shear deformation

    Wetscher, F., Stock, R. & Pippan, R., 2007, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 445-446, p. 237-243

    Research output: Contribution to journalArticleResearchpeer-review

  12. Published

    Characterisation of Residual Stresses in Turbine Discs by Neutron and High-Energy X-Ray Diffraction and Comparisation to Finite Element Modeling

    Cihak, U., Staron, P., Clemens, H., Homeyer, J., Stockinger, M. & Tockner, J., 2006, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 437, p. 75-82

    Research output: Contribution to journalArticleResearchpeer-review

  13. Published
  14. Published

    Comparison of NiAl precipitation in a medium carbon secondary hardening steel and C-free PH13-8 maraging steel

    Erlach, S. D., Leitner, H., Bischof, M., Clemens, H., Danoix, F., Lemarchand, D. & Siller, I., 2006, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 429, p. 96-106

    Research output: Contribution to journalArticleResearchpeer-review

  15. Published
  16. Published
  17. Published

    Compressed Bi-crystal Micropillars Showing a Sigmoidal Deformation State - A Computational Study

    Toth, F., Kirchlechner, C., Fischer, F. D., Dehm, G. & Rammerstorfer, F. G., 2017, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 700, p. 168-174

    Research output: Contribution to journalArticleResearchpeer-review

  18. Published

    Controlling the distribution of structural heterogeneities in severely deformed metallic glass

    Bian, X. L., Zhao, D., Kim, J. T., Sopu, D., Wang, G., Pippan, R. & Eckert, J., 2 Mar 2019, In : Materials Science and Engineering A. 752.2019, 3 April, p. 36-42 7 p.

    Research output: Contribution to journalArticleResearchpeer-review

  19. Published

    Cooperative deformation behavior between the shear band and boundary sliding of an Al-based nanostructure-dendrite composite

    Kim, J. T., Hong, S. H., Kim, Y. S., Park, H. J., Maity, T., Chawake, N., Bian, X. L., Sarac, B., Park, J. M., Prashanth, K. G., Park, J. Y., Eckert, J. & Kim, K. B., 11 Aug 2018, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 735.2018, 26 September, p. 81-88 8 p.

    Research output: Contribution to journalArticleResearchpeer-review

  20. Published

    Corrigendum to “Structural modifications in sub-Tg annealed CuZr-based metallic glass”

    Sarac, B., Bernasconi, A., Wright, J., Stoica, M., Spieckermann, F., Mühlbacher, M., Keckes, J., Bian, X. L., Wang, G. & Eckert, J., Dec 2017, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing.

    Research output: Contribution to journalArticleResearchpeer-review

  21. Published

    Creep properties and creep microstructure evolution of Mg-2.49Nd-1.82Gd-0.19Zn-0.4Zr alloy

    Han, W., Yang, G., Xiao, L., LI, J. & Jie, W., 2017, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 684, p. 90-100

    Research output: Contribution to journalArticleResearchpeer-review

  22. Published
  23. Published
  24. Published

    Deformation mechanisms of a modified 316L austenitic steel subjected to high pressure torsion

    Scheriau, S., Zhang, Z., Kleber, S. & Pippan, R., 2011, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. p. 2776-2786

    Research output: Contribution to journalArticleResearchpeer-review

  25. Published

    Designed heterogeneities improve the fracture reliability of a Zr-based bulk metallic glass

    Li, B. S., Shakur Shahabi, H., Scudino, S., Eckert, J. & Kruzic, J. J., 14 Oct 2015, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 646, p. 242-248 7 p.

    Research output: Contribution to journalArticleResearchpeer-review

  26. Published
  27. Published

    Discrete dislocation simulation of nanoindentation: The effect of statistically distributed dislocations

    Kreuzer, H. G. M. & Pippan, R., 2005, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 400-401, p. 460-462

    Research output: Contribution to journalArticleResearchpeer-review

  28. Published

    Discrete dislocation simulation of nanoindentation: the effect of moving conditions and indenter shape

    Kreuzer, H. G. M. & Pippan, R., 2004, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 387-389, p. 254-256

    Research output: Contribution to journalArticleResearchpeer-review

  29. Published

    Dynamic recrystallization of NI-base alloys-Experimental results and comparisons with simulations

    Poelt, P., Sommitsch, C., Mitsche, S. & Walter, M., 2006, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. p. 306-314

    Research output: Contribution to journalArticleResearchpeer-review

  30. Published

    Effect of back stress evolution due to martensitic transformation on iso-volume fraction lines in a Cr-Ni-Mo-Al-Ti maraging steel

    Tanaka, K., Terasaki, T., Goto, S., Antretter, T., Fischer, F. D. & Cailletaud, G., 20 Jan 2003, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 341, 1-2, p. 189-196 8 p.

    Research output: Contribution to journalArticleResearchpeer-review

  31. Published

    Effect of cerium addition on microstructure and mechanical properties of high-strength Fe85Cr4Mo8V2C1 cast steel

    Hufenbach, J., Helth, A., Lee, M. H., Wendrock, H., Giebeler, L., Choe, C. Y., Kim, K. H., Kühn, U., Kim, T. S. & Eckert, J., 30 Sep 2016, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 674, p. 366-374 9 p.

    Research output: Contribution to journalArticleResearchpeer-review

  32. Published
  33. Published
  34. Published
  35. Published

    Effect of thermal treatment on microstructure in high pressure torsion (HPT) deformed nickel

    Schafler, E. & Pippan, R., 2004, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 387-389, p. 799-804

    Research output: Contribution to journalArticleResearchpeer-review

  36. Published
  37. Published

    Enhanced mechanical properties of Al2O3-C refractories with silicon hybridized expanded graphite

    Wang, Q., Li, Y., Jin, S., Sang, S., Xu, Y., Xu, X. & Wang, G., 2 Jan 2018, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 709, p. 160-171 12 p.

    Research output: Contribution to journalArticleResearchpeer-review

  38. Published

    Erratum to "On the experimental characterization of crystal plasticity in polycrystals"

    Tatschl, A. & Kolednik, O., 2004, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. A 364, p. 384-399

    Research output: Contribution to journalArticleResearchpeer-review

  39. Published

    Evolution of misorientation distribution during warm 'abc' forging of commercial-purity titanium

    Mironov, S. Y., Salishchev, G. A., Myshlyaev, M. M. & Pippan, R., 2006, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 418, p. 257-267

    Research output: Contribution to journalArticleResearchpeer-review

  40. Published
  41. Published

    Friction welding of selective laser melted Ti6Al4V parts

    Prashanth, K. G., Damodaram, R., Maity, T., Wang, P. & Eckert, J., Sep 2017, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 704, p. 66-71

    Research output: Contribution to journalArticleResearchpeer-review

  42. Published
  43. Published
  44. Published

    Hardening and microstructure reactions in high-temperature Equal-Channel Angular Pressed Mg-Nd-Gd-Zn-Zr alloy

    Li, J., Sha, G., Xu, W., Xia, K., Jie, W. & Simon, R., 2010, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 527, p. 5092-5099

    Research output: Contribution to journalArticleResearchpeer-review

  45. Published
  46. Published
  47. Published
  48. Published
  49. Published

    Impact of the B2 ordering behavior on the mechanical properties of a Fe Co Mo alloy

    Turk, C., Leitner, H., Kellezi, G., Clemens, H., Gan, W., Staron, P. & Primig, S., 2016, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 662, p. 511-518 8 p., 662.

    Research output: Contribution to journalArticleResearchpeer-review

  50. Published

    In situ formation of carbon nanotubes and ceramic whiskers in Al2O3-C refractories with addition of Ni-catalyzed phenolic resin

    Luo, M., Li, Y., Sang, S., Zhao, L., Jin, S. & Li, Y., 15 Dec 2012, In : Materials science and engineering: A, Structural materials: properties, microstructure and processing. 558, p. 533-542

    Research output: Contribution to journalArticleResearchpeer-review

  51. Published
Previous 1 2 3 Next